It may be detected, but just not be auto-mounting. You do not need to perform another low level format on this drive unless you decide to perform certain diagnostics through the controller. Posted by theflash1932 on 10 Mar 2016 16:56 Verified Answer Verified by KozPeace KozPeaceI've heard that hot spare is not a good backup system and using RAID system is more efficient My primary hardrive is showing signs of failure. http://webcomputerrepair.com/how-to/how-to-fix-a-crashed-hard-drive.html
Using a Sata to usb failed, my imac did not even recognize the hard dr solved RIAD/SAS controller card and backplane drive cage vs SATA to SATA only drive setup? It might also be prudent to check the motherboard documentation for information on the proper procedure for connecting additional hard drives. KozPeace On another note, I have a windows 2008 R2 server with two 500GB. Low level formats can take up to 90 minutes for ST3146854SS models, 60 minutes for ST373454SS models or 30 minutes for ST336754SS models. http://knowledge.seagate.com/articles/en_US/FAQ/218751en
Posted by theflash1932 on 16 Feb 2013 14:22 Verified Answer Verified by director87 "Do I have to buy dell certified drives?" You don't HAVE to, but there is no guarantee that Posted by director87 on 16 Feb 2013 15:36 Thank you. Again, thanks for your help. After you assign it as a hot spare it should start rebuilding.
RAID should be implemented based on performance and availability needs. Installing Windows 7/Vista, simply click on Load Driver once given the opportunity to do so. Operating systems Cheetah disk drives are designed to operate with a variety of operating systems. How To Wipe Sas Drive A better option than a hot-spare is double redundancy, as exists with a RAID 6 (and sometimes RAID 10).
The Barracuda is not just "non-certified", but it is also not enterprise-class, which can introduce a whole new set of problems and are really not suitable for use on RAID controllers. How To Connect Sas Hard Drive To Pc Keep the drive in its antistatic container until you are ready to install it. None. Power is supplied through the SAS connector.
Most systems that host only a couple of drives enable all of the drives to start up immediately when power is applied to the drives. Sas Controller Card For Pc If you see it in SAS Topology then use CTL D to pull up additional options. Register. 09-16-2011 #1 kmlrao View Profile View Forum Posts Private Message View Articles Just Joined! With a SAS interface, each disk drive has its own cable that connects directly to a SAS host adapter (also called a SAS controller).
See the controller card documentation for guidance on how to confirm that your controller drivers have been loaded correctly. http://h20564.www2.hpe.com/hpsc/doc/public/display?docId=mmr_kc-0115156 Mount the drive to the carrier or tray provided by the host system using four 6-32 UNC screws. How To Format Sas Hard Drive Handle the drive only by the edges or frame. Sas Controller Driver For Windows 7 If not, reboot and enter the BIOS (usually the Del or F1 or F2 key).
You should see a list of all of the drives the controller detects. Check This Out Do not drop or jar the drive. If you don't see it in SAS Topology then it does not appear the controller is able to properly communicate with this drive. Upgrade An Easy Way to Bigger and Better. Sas Host Adapter Setup Utility
See the SAS controller documentation to determine how to assign the drive to an array. SATA hard drive not recognized via USB steve54321May 16, 2015, 8:31 PM This sounds a very basic concept but I am really confused. Have you checked the output of dmesg for any hints?, e.g.: Code: dmesg|grep sd Is it possible to download and boot the CentOS 6.0 LiveCD, to see if the updated kernel Source Format the drive The drive has been low level formatted at the factory.
The new drive should not have anything in the "Drive Status" field. Sas To Sata Adapter Not Working All Replies Posted by DELL-Daniel My on 16 Feb 2013 14:22 Verified Answer Verified by director87 Hello director87 Go to RAID Properties>Manage Array>Manage Hot Spares. KozPeace On another note, I have a windows 2008 R2 server with two 500GB.
The new drive should not have anything in the "Drive Status" field. Can't find your answer ? DELL.COM > Community > Support Forums > Servers > PowerEdge HDD/SCSI/RAID Forum > New HDD not being recognized by SAS controller on PowerEdge T410 Shop > Home & Home Office > Sas To Usb take Disk 1 and put new 1TB and then SAS Controller to tell it's part of RAID 1?
To start viewing messages, select the forum that you want to visit from the selection below. ** If you are logged in, most ads will not be displayed. ** Linuxforums now You can replace the smaller drives with larger ones, BUT your array will NOT get any bigger. You can replace the smaller drives with larger ones, BUT your array will NOT get any bigger. have a peek here Many SAS RAID controllers require that a drive be assigned to an array before it will allow the operating system to see the drive.
Questions About SAS, SATA, and Hard Drives solved Using internal hard drive as external hard drive via HP SimpleSave SATA to miniUSB converter board solved SATA Hard Drive not recognized in So I am kind of worry that the other one goes down..can't effort.. RAID's purpose is to protect the availability of the server and its data and services and/or increase performance and/or capacity of a storage system. The USB port of course connects to PC directly.
So I am kind of worry that the other one goes down..can't effort.. In one of the main screens of the BIOS you should see detected hard drives. Hard drive only recognized via usb suddenly solved Windows 7 repeatedly asking to reformat internal hard drive connected via sata to usb connector (like an external) Do all Hard Drives work I turned off the server and switched the cables from the primary to the new drive, to see if it would make a difference.
It might also be prudent to check the motherboard documentation for information on the proper procedure for connecting additional hard drives. RAID's purpose is to protect the availability of the server and its data and services and/or increase performance and/or capacity of a storage system. Verify that the drive is enabled by the SAS host adapter setup utility. Unlike (Parallel) SCSI, there is no need to set an ID, since each drive connects directly to its own port and since the controller will assign all IDs.
Like 0 Reply You have posted to a forum that requires a moderator to approve posts before they are publicly available. Join Date Sep 2011 Posts 3 SATA SAS Hard drive is not detected Hello, I have purchased a new Hard disk of 500Gb( "WD5000BEVT" SATA-SAS drive). Please consult the motherboard or SAS controller documentation for assistance with entering into the SAS BIOS setup. Special note for users of a RAID host adapter. If you do decide to perform a low level format, do not abort the format as this is likely to make the drive inoperable.
Use the arrow keys to highlight the new drive and the +/- keys to assign it as a hot spare.